Southeastern-FL
Truss Plant #1
Closing!

Equipment for Sale!

Southwestern-AZ
Truss Plant #3 Closing!

Equipment for Sale!

Southwestern-NM
Truss Plant #4 Closing!

Equipment for Sale!

Southeastern-FL
Truss Plant #5
Closing!

Alpine
Equipment for Sale!

2004 TCT Linear Saw purchased in January of 2004 / Model # CT041-1100 and upgraded by TCT in 2005 to run the 1150 softwar /. The upgrade included TCT’s Dual Feedback upgrade package which brought the saw up to 1150 cutting capability / The difference of this saw and a factory built 1150 is that the angulation is controlled by a servo-gearbox combo instead of the direct drive servo that comes on a standard 1150 / The saw now cuts 2x4 and 2x6 chords, webs, wedges, scissor bottoms chord cuts, 4-angle pieces as short at 13 inches and 3 angle pieces as short as 3 inches / This saw will also cut down to 11 degrees on 2x4 verses and the feed rate was increase to 5 feet per second / Included is a 5 HP motor with a 24" blade, a standard TCT scrap conveyor and a Mathews Inkjet marking system / 240 volt, 3 phase / $84,450.00 FOB Southeast-FL

2004 TCT Linear Saw Series 1000 / model # CT041-1000 / Purchased in January of 2004 / The saw cuts only 2x4 material / 5 HP motor with a 24" blade, a standard TCT scrap conveyor / 240 volt, 3 phase / FOB Southeast-FL

2001 Cyber Saw / Frame # 232 / 5 bladed saw; 1-32", 2-20", & 2-16" plus complete extra set / Purchased new / 240 Volts / $83,000.00 FOB Southeast - FL

1999 Mitek Cyber Saw model 2000 / Bought new / Recent 10k dollar computer upgrade & 6k dollar onsite Mitek Maitenance / serial # 154 / MFG. 10-1999 / - Fully automated/ manual five-blade component saw . Cutting performed by 2-16" X 6HP, 2-20" X 6HP, 1-32" X 12.5HP, touch screen controls for fully automated or manual part input, all powered movements, cuts 2x4 thru 2x12, 4x2, belt conveyor / $77,000.00 FOB MT

1997 Cyber Saw / Frame # 22 / Rebuilt including computer upgrades, Monitor, ect. at a cost of $26k / 5 bladed saw; 1-32", 2-20", & 2-16" plus complete extra set Purchased new / 240 Volts / $74,000.00 FOB Southeast - FL

2003 TCT Web Saw 679 / Model Ct041-1000 / SN # 02C622/02F090 / Extra transformer / Spare blade / 240 volts / List $68,000

1998 Alpine Auto-mill / Unit #510 / SN # 343-015 / 480 Volt / $68,000 FOB FL

1998 Alpine Automill / Unit #511 / SN # 343-016 / Extra printer / 480 volt / $68,000 FOB FL

Alpine TimberMill 6-20G (no digitals) / Component Saw / Cuts Roof & Floor Truss Components / 6 Balded motors w/ power angulations / Power Driven Carriage / Power Bottom Waste with Power Waste Incline / $32,500.00 FOB PA

1985 Alpine TimberMill model # MH6B-20 / Serial # PO198 / 480 volts / Cuts Roof & Floor Truss Components / 6 Bladed motors w/ power angulations / 3 blades / Power Driven Carriage / Power Bottom Waste / No incline / $32,000.00 FOB NC

1994 Clary Auto Master / Model: 341 / Serial # : 341G15 / $30,000.00 FOB PA

2005 Alpine FT web pro saw / serial number 6608005006 / 480 Volts  3 Ph / $28,000 FOB Southeast-FL

1997 Timber Mill Saw / Model # MH4G-14 / Serial # AB0691 / 4 motors / 3 blades / No incline / 440 volts 3 phase / $22,000.00 FOB NC

1997 Alpine Speedcut Express Saw w/2004 Alpine Express Retrofit AC 2393 SSA-17
20’ in feed conveyor w/ Speed Measure and 10’ out feed conveyor / $18,000.00 FOB NM

TCT EZ Trim Beveler / Model CT041-2000 / The absolute fastest and safest way to cut double bevels on jack chords and like pieces. The EZ-Trimmer is totally enclosed for maximum safety and has an average cycle time of 15 pieces per minute. The EZ-Trimmer can be used as a stand alone unit or it can be attached to and powered from any TCT WebSaw / Cuts double bevels on pitches from 0/12 to 12/12 including 2x6 lumber and smaller. /$10,500 FOB FL

TCT Trim Beveler / Unit #1348 / Model EZ Trim / 240 volt / $10,500 FOB FL

Alpine Metracut Auto Saw / Unit #506 / Model Smartcutter / 480 volt / $8,000 FOB FL

1998 Alpine Metracut Centerline / Unit #490 / Model SSA-17 Speed Cut / SN # AC2360 / 440 Volt / $8,000 FOB FL

1998 Alpine Metracut Centerline / Unit #489 / Model SSA-17 Speed Cut / SN # AC2359 / 480 Volt / $8,000 FOB FL

Clary Master Saw / 480 Volts / (5) Blades (32/22/16/16/18) / Shaker Waste Pan w/ Incline / Powered Angulations on all Blades / Powered Centerline Height Adjustments / Air Brakes / Cuts 2x4 through 2x12 Materials / On Edge RT Cuts 16.75" Min & 20'-0" Max On Flat Cuts FT 16.5" Min. / (Cuts RT and FT Webs ) / FOB SC

Alpine Metracut Centerline / Unit #491 / Model SSA-14 Speed Cut / SN # N1325 / 440 Volt / $4,000 FOB FL

Alpine Metracut Centerline / Unit #493 / Model SSA-14 Speed Cut / SN # N1304 / 440 volt / $4,000 FOB FL

Alpine Metracut Centerline / Unit #488 / SN # 55AIN / 480 volt / $3,000 FOB FL

2002 Mi-Tek Roof Truss Line / 120 feet of table space / Center Fed Conveyors / (2) 14' x 24" gantry heads / (1) 14' x 24" finish roller / Model # 87700-502 / 575 Volts / 3 phase / $160,000.00 USD FOB Milton, Ontario*

• 1 Mitek finish roller
• 2 Mitek 14’ x 24” gantry rollers
• 17 slotted tables 6’ each plus a 15” spacing
• 14 drive rollers
• 14 idle rollers
• 12 receiver assemblies with actuators
• 14 sections of rail totaling 260’ of rail (120 feet plus 10’ on the end to rest the gantry times 2 sides)

*75' Table Space and 3rd Gantry Head available at additional cost!

6 Mitek Stackers/ Control Console (may be divided up) / Single centerline feed / The peak-up stacker holds up to 30 trusses and can easily stack any truss from 16' to 60' in length. With the use of dual Peak-Up Stackers, they can hold 80' trusses. The average stacking cycle is 40 seconds. When the peak-up stacker is placed outside, it saves valuable in-plant space.

1989 Alpine Gantry / Unit #486 / 2 Gantry Heads / 17 tables / SN # 15-102 / 480 volt / $70,000 FOB FL

1989 Alpine Gantry / Unit #487 / 2 Gantry Heads / 17 tables / SN # 15-102 / 480 volt / $70,000 FOB FL

1994 Klaisler Side Eject Roof Truss Gantry / 18 Steel bottom plastic top tables / Pop-up Side Eject / (1) 14' x 24" gantry head / Air supply / Jigging hardware / bridge plates for the aisles / Includes 16 receivers / 16 ejectors / 46 slider pads / Bottom chord jigging /  14 powered and 14 idle roller beds / s/o electrical chord / rail and stops.  / 240 volt / 3 phase electrical service / $54,650.00 FOB FL

2002 Klaiser 52' Gantry System / End Eject / GR314-24 2355 / 7 tables w/plastic tops and air ejectors / $50,000 FOB NM

1995 Circa 60' Gantry / (9) Tables (4 Mitek & 5 Diamond) / (1) Mitek Roller Gantry / (72) FT of Rail / 60ft+ spaced working / 54ft working pushed together

Klaisler Gantry Head (14') / Reconditioned by Rand Manufacturing 06-2007 / Model 14G / (2) New 5 HP motors / New bogie wheels / $18,500.00 FOB NC

2005 Klaiser Finish Press Roller TR214-24 / $18,000

Alpine Finish Roller / Unit #478 / SN # 720-036 / 480 Volt / $4,000 FOB FL

Rebuilt Finish Roller / Unit #480 / 480 volt / $2,000 FOB FL

Clary 14’ x 20" Finish Roller (Reconditioned 05/07)

Klaisler Finsh Roller #1 (12' x 18" x 1/2") / Reconditioned by Rand Manufacturing / 2 5 HP Supermax-Tatung motors with 2 David Brown gear boxes / 230 volts 3 phase / adjustable height

62' Railrider Floor Truss Roller with RailRider Pro Tables / Pneumatic truss flippers & pop-ups / Side ejects to powered 72'  (48' inside / 24' outside) Outfeed conveyor system / Air powered clamping / Air lines and cylinders mounted under table / 24" Gantry Roller /  10-Hp shaft-mounted / Softstart gear motor / Overhead plate rack / 3/4" Steel top tables / 460V 3 Phase power. / $78,700.00 FOB NJ

2005 Mitek 42' Railrider Pro Floor Truss Gantry /Serial # 122005230375.3 / The 40' table features 42' of jigging space and comes equipped with gantry head parking areas on both ends. Pneumatic jigging has automatic depth adjustment for jigging two trusses. The air cylinders are placed under the table for added space and additional safety.  Consistent plate embedment is achieved with a 24" diameter roller press. A new electronic soft-start cushions startup and shutdown shock, prolonging the life of your machine. The pneumatic controls are located on pedestals for your convenience./ 240 volt 3 phase / $45,000.00 FOB-AZ

1989 Alpine Mighty Mite w/ Floor Jigging / Model: 5M27 / Serial # : 19-555 / Condition: Good (still in use) / $11,200.00 FOB PA

1998 Alpine Splicer / Unit #494 / SN # 722-038 / 480 Volt / $2,500 FOB FL

1985 Trailer is in good condition and was overhauled in 2006 with fresh paint, wiring and good tires.  48’ with fixed dual axles. / 70% Tires / $6,500.00 FOB CT

1999 JDH 40' trailer / Unit #11 / Hydraulic / fifth wheel / fixed tandem axle / locking rollers / top three rollers split / VIN # 1L9RD3620XC094583 / $11,900.00 FOB FL